Van-air-systems ID15/IND Bedienungsanleitung PDF herunterladen

ZZZYDQDLUV\VWHPVFRP

0IGLQ86$ 

&$3$&,7<6&)0#36,*0:336,*

0D[,QOHW7HPSHUDWXUH)

)25'5<,1*&2035(66('$,525*$6

0RGHO1R,',1'

&DUWULGJH1R06

287

1/4" BALL VALVE

2950 Mechanic Street

Lake City, PA 16423-2095

Phone: 814-774-2631

Fax: 814-774-3482

www.vanairsystems.com

INSTALLATION INSTRUCTIONS

IN-LINE DESICCANT DRYER MODEL ID15/IND

VAN AIR PART NUMBER: 38-0124

FOR DRYING COMPRESSED AIR OR GAS TO -40°F PRESSURE DEWPOINT

BOSS (INSTALL CARTRIDGE HERE)

O-RING

GROOVE

VIEW FROM BOTTOM OF DRYER HEAD

BOWL

(NOTE: CARTRIDGE SHIPPED IN BOX

WITH DRYER.)

REPLACEMENT PARTS

DESCRIPTION

DRYER HEAD

DRYER BOWL

MS-16 CARTRIDGE

MOISTURE INDICATOR

HOUSING O-RING

HOUSING CLAMP

1/4" NPT BALL VALVE

VAN AIR PART NO.

201-00053

201-02002

26-0889

38-0114

475-00235

471-00100

290-00011

Locate dryer as close as possible to equipment to be

protected.

Where condensed moisture is present in the air line, install

a separator with drain valve upstream of dryer.

Install inlet and outlet valves for isolating dryer during

cartridge change.

Check markings on head of vessel; then connect inlet piping

to side marked "A" and outlet to side marked "B".

If there are any sudden air surges downstream of dryer,

install a flow control device after the dryer.

Remove plug from the top of head and install moisture

indicator securely into head.

Install MS-16 cartridge as outlined below.

INSTALLING MS-16 CARTRIDGE:

Close dryer inlet and outlet shutoff valve. Slowly open drain

on bottom of bowl until vessel is completely depressurized.

Grasp bottom portion of housing (bowl) with one hand and

turn clamp knob with the other to loosen. Slide clamp down

and off vessel.

Remove used cartridge from head and discard the cartridge.

Remove new cartridge from box and vapor seal bag.

Push new cartridge onto boss of dryer head.

Reinstall bowl and clamp. Make sure that the bowl is tight

against the head and the o-ring is correctly seated in the

groove.

Close the ball valve and slowly repressurize the vessel. If

any leaks occur, depressurize vessel completely and correct

the problem.

March 2009

P/N: 432-00107-E

WHEN TO REPLACE CARTRIDGE:

Crystals in moisture indicator will change from blue to

pink when molecular sieve in cartridge is saturated with

moisture. Install a fresh cartridge when moisture indicator turns

pink. When air supply is reconnected, moisture indicator will

turn blue again and remain blue until another cartridge change

is required.

MS-16 MOLECULAR

SIEVE CARTRIDGE

CLAMP

INLET

1/2" NPT

OUTLET

1/2" NPT

HEAD

MOISTURE

INDICATOR

ID15/IND

INSTALLING ID15/IND DRYER:

Inhaltsverzeichnis

Seite 1 - VAN AIR PART NUMBER: 38-0124

ZZZYDQDLUV\VWHPVFRP0IGLQ86$ &$3$&,7<6&)0#36,*0:336,*0D[,QOHW7HPSHUDWXUH))25'5<,1*&am

Kommentare zu diesen Handbüchern

Keine Kommentare

Van-air-systems ID15/IND Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Van-air-systems ID15/IND herunter. Van Air Systems ID15/IND User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Van-air-systems ID15/IND